Відео

Great channel. Can you tell us how to calculate the interface level

How to connect hart

Thank you very much.

How to get analog output ma from del p inwater column?

Excellent explanation Sir🎉

Can I do the calibration without mounting the positioner on the valve ???

How can we make RTD sensor circuit?

Mines says negative drift after the remove gas prompt

Well understood, the Video is Educative and understanding

Fantastic information

Zero it out

Can we enter negative temperature value in the minimum temperature range ?

very usefull

You used math to show two wire but not 3 wire. Could u do a vid with math for 3 wire so we can actually see its better

I think you should use numbers to see that this only works if the fraction of resistors on the left side is one over one(same resistor top and bottom) not some other fraction like one over two e.t.c Because you can have a balanced bridge (the same fraction on both sides say 1/2 ) And get there with the variable resistor but it will be wrong. E.g with 10/20 resistors on left side i pretended to have 10 ohm resistive legs for sensor but with a 90 ohm sensor. That meant to variable resistor would stop at 40 as (40+10=50) top resistor and (90+10=100) bottom resistor giving a balanced bridge 1/2=50/100 but when we take to 40 we are yetting on variable and try to work out the sensor restance as we dont know we get 80 and not the desired 90 that it is.

Great video

Hey man. This is some great content. If you made a full process automation course I would buy it. Keep it up. Greetings from Istanbul 👍

Good explain

ua-cam.com/video/HBBK-yzz_RY/v-deo.htmlsi=uempybj9iVvbXBBe

VIDEO is super nice explain but video is high

Loto explain Loto-logout tagout

Very helpful video

You should not pick a valve size with less cv then the calculated cv, incorrect.

ua-cam.com/video/F14HBI81Rj4/v-deo.htmlsi=jSYNbDJ5fKZegkWu

Excellent video. Just one question, why do you use de Sf for Glycerine? Does it matter which Sf fluid is used?

Please help me with this What will be the output from temperature transmitter

More videos please.you are doing a good job.keep it going.

Flow meter settings, I have been told many different settings.

How to calculate that resistance?

If the boiler is idle or not at operating pressure, how does this effect the level? Will the LRV and URV need to be trimmed until the boiler is at operating pressure?

Goog job

Thanks Sir for explaining, can you explain pressure switch principle work.

Please can you make a video on how to perform calibration of gas chromatograph using mono2020 software

Does DPT has two equalizing valve as shared in this video? I thought it has only one equalizing valve,2 block valve and two vent valve.

Well explained, appreciate your efforts

Gosh, we've replaced so many of these with Hart-smart positioners, but I've calibrated so many of these and other positioners and I/Ps over 42 years.

How adjust travel length in positioner

Hello everyone this vedio is so useful for me thanks to the channel admin and do a lot of this kind of vedio 😊and in the future I will be great engineer and I will do a lot of great vedios about this field in my language ..from Uzbekistan❤

Please do more instrumentation

Please make a video how to connect the transmitter to input of plc and how it works

It is called a FLow-meter. It is also called a rotameter.

How can I communicate with you please

Magnesium Chloride equilibrates to 33%RH, not 13%RH... www.engineeringtoolbox.com/salt-humidity-d_1887.html cameo.mfa.org/wiki/Saturated_salt_solutions nvlpubs.nist.gov/nistpubs/jres/81a/jresv81an1p89_a1b.pdf

Thanks

I would love to know possible questions for instrumentation in acid plant. I'll appreciate

Hi I want to re range the transmitter from 200 l/sec to 300 l/sec what should I do

Good

Can I use the transmitter as a 2 wire or 4 wire

Fantastic

Very well explained 🎉